Fundamental Plumber Guide for Bathtub Installation
Fundamental Plumber Guide for Bathtub Installation
Blog Article
What're your thoughts concerning A Step-by-Step Guide to Installing a Bathtub?
Mounting a bathtub isn't precisely brain surgery, however it does need solid plumbing, woodworking, and occasionally, tiling abilities. Replacing an old bath tub with a new one is additionally a moderately difficult job. If the old tub is easily accessible, the project can relocate rapidly; if you have to open up a wall surface to eliminate the old tub and place the brand-new bathtub, the task is a lot harder. In either situation, the task is within a home handyman's abilities, although you will need a helper to leave the old bathtub as well as embeded in the brand-new one. Make certain you have actually certified yourself for the job and fit trying it. Rather than hiring a contractor to take control of a halfway-completed job, it is much better to consider employing one before you start. Chances are you might require a professional plumber to make tube links.
This short article will certainly aid you install a brand-new bath tub in your bathroom if you have already bought a brand-new bathtub and do not need to transform the plan of your previous water supply pipes.
Your tools as well as material list ought to consist of the following:
Getting ready for the Setup
To start with, the sustaining framework supplied with the bath needs to be fitted (if needed) according to the supplier's instructions. Next, fit the taps or mixer to the bath tub. When fitting the faucet block, it is very important to ensure that if the faucet comes with a plastic washer, it is fitted in between the bath and also the taps. On a plastic bathroom, it is also reasonable to fit a sustaining plate under the taps unit to avoid pressure on the tub.
Fit the flexible tap connectors to the bottom of both taps using 2 nuts and also olives (sometimes supplied with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet hole, and then pass the outlet through the hole in the bathroom. Make use of the nut supplied by the producer to fit the plug-hole. Analyze the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next off, fit completion of the versatile overflow pipeline to the overflow electrical outlet. Afterwards, screw the pipeline to the overflow face which must be fitted inside the bathroom. Make sure you utilize all of the supplied washing machines.
Link the catch to the bottom of the waste electrical outlet on the bath tub by winding the thread of the waste outlet with silicone mastic or PTFE tape, as well as screw on the trap to the outlet. Link the bottom of the overflow tube in a comparable manner.The bath should now be ready to be fitted in its final position.
Removing Old Touches
If you require to replace old taps with new ones as a part of your installation, after that the first thing you must do is detach the water supply. After doing so, turn on the taps to drain any water continuing to be in the system. The procedure of eliminating the existing taps can be rather troublesome as a result of the limited accessibility that is commonly the situation.
Use a container wrench (crowsfoot spanner) or a tap device to undo the nut that connects the supply pipes to the taps. Have a fabric all set for the remaining water that will originate from the pipelines. Once the supply pipes have actually been removed, utilize the same tool to loosen up the nut that holds the faucets onto the bath/basin. You will certainly need to stop the single faucets from transforming throughout this process. Once the faucets have been removed, the holes in the bath/basin will certainly have to be cleaned up of any type of old sealing substance.
Prior to proceeding to fit the brand-new taps, compare the pipe connections on the old taps to the new taps. If the old taps are longer than the new faucets, then a shank adapter is needed for the new taps to fit.
Installing the Bath tub
Making use of the two wooden boards under its feet, position the tub in the called for placement. The wooden boards are handy in equally spreading out the weight of the bath tub over the area of the boards rather than focusing all the weight onto four tiny factors.
The next goal is to ensure that the bath tub is leveled all round. This can be accomplished by examining the level and readjusting the feet on the bathtub until the level checks out degree.
To set up taps, fit all-time low of the furthest flexible faucet connector to the ideal supply pipeline by making a compression join; after that do the very same for the other faucet.
Switch on the water supply as well as check all joints and brand-new pipework for leaks and also tighten them if needed. Fill the tub as well as additionally inspect the overflow electrical outlet and also the regular electrical outlet for leakages.
Lastly, deal with the bathroom paneling as described in the producer's instruction manual. Tiling and also sealing around the bath tub ought to wait up until the bath tub has actually been used at the very least once as this will settle it right into its last setting.
Suitable New Touches
If the tails of the brand-new taps are plastic, then you will need a plastic port to avoid damages to the thread. One end of the port fits on the plastic tail of the faucet and also the various other end provides a connection to the current supply pipelines.
If you need to fit a monobloc, then you will call for minimizing couplers, which attaches the 10mm pipeline of the monobloc to the basic 15mm supply pipeline.
Next off, place the tap in the placing hole in the bath/basin ensuring that the washers remain in place between the tap as well as the sink. Safeguard the tap in place with the supplier given backnut. As soon as the faucet is firmly in place, the supply pipes can be linked to the tails of the faucets. The faucets can either be attached by using corrugated copper piping or with normal faucet connectors. The former kind ought to be linked to the faucet finishes initially, tightening up just by hand. The supply pipelines can later on be connected to the various other end. Tighten both ends with a spanner after both ends have been linked.
Tiling Around the Tub
In the area where the bathroom satisfies the tile, it is required to secure the joins with a silicone rubber caulking. This is very important as the installation can move sufficient to crack a stiff seal, creating the water to penetrate the wall between the bathroom and also the tiling, resulting in difficulties with dampness and also feasible leakages to the ceiling listed below.
You can pick from a range of coloured sealants to assimilate your fixtures and also fittings. They are sold in tubes and cartridges, and also can securing spaces up to a width of 3mm (1/8 inch). If you have a bigger gap to load, you can load it with twists of drenched newspaper or soft rope. Remember to always fill up the bath tub with water prior to securing, to permit the motion experienced when the tub is in usage. The sealer can split rather early if you do not take into account this motion prior to sealing.
Alternatively, ceramic coving or quadrant floor tiles can be made use of to border the bath or shower tray. Plastic strips of coving, which are easy to use as well as cut to dimension, are likewise easily offered on the market. It is advisable to fit the ceramic tiles utilizing water-resistant or water resistant sticky as well as cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
I'm certainly very curious about How to Install a Bathtub and I am hoping you enjoyed reading the entire blog entry. Liked our piece of writing? Please share it. Help someone else check it out. Thank-you for taking the time to read it.
Book Service Report this page